Soundscape Console Manager V1.5.4                             September 27, 2005
________________________________________________________________________________

Changes since V1.5.4
____________________

- Multiple HUI device support
  
Changes since V1.5.3
____________________

- Bug fixed which caused bad operation if more than 1 track insert is placed 
  in a mixer column
- Up to 7 Mackie Control Extension units support
  

Changes since V1.5.1
____________________

- Bug fixed, 'Master' fader is found in Win98 environment
- Check for 'Master' fader is case independent

Changes since V1.5
__________________

- Bug fixed: Zoom buttons operation corrected


Changes since V1.5 Beta 4:
__________________________

- Bug fixed: Correct button for shift is used
- Bug fixed: Move second goes in correct direction

Changes since V1.5 Beta 3:
__________________________

- Master fader will connect to column labeled with "Master"
- Function buttons 1-14 selects tool on current toolpage
- Function button 15 decrements toolpage
- Function button 16 increments toolpage


Changes since V1.5 Beta 2:
__________________________

- Support for Mackie Controller XT
- Console Manager can support 1 Mackie Controller and 3 Extensions,
  where the main controller must be placed the right side of the 
  extension units.


Changes since V1.5 Beta 1:
__________________________

- Support for Mackie Controller (implementation details below), tested with 
  firmware version V1.01
- Support for Mackie Baby Hui (implementation details below), tested with
  firmware version A8


Changes since V1.4.1:
_____________________

- Basic support added for Mackie Controller (implementation details below)


Changes since V1.4:
___________________

- Buf fixes in 9-pin master interface which prevented locating to a frame other
  than 0


Changes since V1.3:
___________________

- Installation problems fixed
- Problems fixed that caused problems with some midi cards


Changes since V1.2.1:
_____________________

- New SOny 9 Pin Master Interface 
- New Spirit Digital 328 V2 (Closed loop) interface
- Midi Mixer Map Interface can control up to 8 sends now
- Bug fixes Midi Mixer Map, MMC Interface
- Improved functionality for MCS bridge and surround panner 
- Support for MCS Orbiter and MCS Track Arming Controller 
	(both units requires new firmware because of conflicts in the protocol)
- Bug fixed which cause potential deadlock with scrubbing/locating
- MMC interface supports Mackie d8b
- Bug fixed that prevented Console Manager to work on NT with user access rights


Changes since V1.2:
___________________

- Usage of snapshot button on Mixtreme will update all mixer parameters of 
  connected interfaces
- Bug fixed in Midi Mixer Map file loading and saving


Changes since V1.1:
___________________

- Full Frame Message decoder allows now editing in arrangement when input is 
  not changing
- Bank settings are saved for CS-10, MCS-3800, MM-16, DC-16, MotorMix and HUI
- Bug fixed in Midi Mixer Map file loading and saving

                                                                                                                     
Minimal software requirements:
______________________________

- Windows NT4 SP4 or higher, Windows 2000, or Windows 95/98 with DCOM 95/98 installed.
- Internet Explorer 4.0 or higher.
- Soundscape Editor software version 3.1 or higher and/or Mixtreme software V1.2.


Introduction
____________

The Console Manager provides a completely new way of connecting multiple controller devices to the 
Soundscape R.Ed and SSHDR1-Plus DAWs and/or to the Mixtreme PCI Card. The interface is built around
a flexible 'plug-in' type architechure, both for different types of controllers and for different
types of interface ports. This makes it easy to add support for future controller models and 
interfaces.  Allowing multiple instances of the same interface makes it possible to create 
different setups or to use multiple consoles on different interface ports.

In V1.5 the following controller devices are supported, some are advanced hardware controllers 
with moving faders:-

JL Cooper CS-10/2
Penny & Giles MM16
Penny & Giles DC16
JL Cooper MCS-3000/3800 (and all expansion accessories)
Mackie HUI
Mackie Baby HUI
Mackie Control
CM Automation Motormix
TASCAM TM-D4000 
Soundcraft Spirit 328
Sony 9 Pin Slave (via RS422)
Sony 9 pin Master (via RS422)
MTC Full Frame Decoder Slave
MMC Slave Interface
Midi Mixer Map (Controller Messages)
Advance MIDI (NRPN) Controller Messages

Most Digital Mixing Consoles that transmit MIDI messages from their faders will work with the 
Basic MIDI Controller Messages interface.


Usage:
______

Start the Soundscape Editor application and select "Connect to Console Manager" in the 
preferences menu (Settings|Preferences). The Console Manager Configuration Dialog should appear now.

When you save the Editor settings with this option enabled, the Console Manager will 
automatically start when the editor application is launched.

When Console Manager is started, a small icon will be shown on the taskbar.
Double click this icon to popup the Console Manager configuration dialog.

Use the buttons to create communication devices, to select devices for the interfaces that
you would like to use, and enable these interfaces (click the checkbox). 
You can use multiple different types of interfaces as long as each has its own MIDI or Com (serial) port.
All settings will be saved automatically when the Console Manager application is closed.

The Console Manager will terminate automatically when the Editor application is terminated 
and the Console Manager configuration dialog is closed.


Currently, the following consoles are supported:

Mackie Baby HUI
_______________

Fader columns:
    Fader controls volume fader of the output element of the selected column.
    Mute button controls the mute of the output element of the selected column.
    Solo button controls the solo of the output element of the selected column.
    Pressing SHIFT and VPOt button works as Rec/Rdy button, to control the arming of 
    the track insert in the column.  Only one track insert per column can be controlled.
    The V-pot controls the panning of the output element or the panning or volume of the 
    selected send element, depending the selected mode Which is defined by the buttons 
    at the right side of the V-pots.
    Using the VPot while pressed will control the vertical panning (surround outputs only) 
    or the panning of the selected send element

Transport buttons:
    They work the same way as the transport buttons on the Editor. 
    
Bank/Channel Select:
    Bank select shifts faders by 8 positions, while channel select shifts faders by 1 position.
    Software is not able to update the display, so it might not indicate correctly which
    faders are under control.

Automation buttons:
    This functionality is not available at this moment


Mackie Controller
_________________


Faders, Panning, Mute, Solo and Rec button:
    The eight faders, mute and sole button are linked to the corresponding controls of the output
    elements of the linked mixer column.  Top line of display shows name of linked mixer column,
    bottom line of displays shows value of the volume control.
    Use the Fader Banks buttons to link to other mixer columns than the first 8.
    Master fader will connect to column labeled with "Master", column 0 if not available

Assignment Section:
    Used to choose sends or plugins of the selected channel.
    VPot buttons are used for the selection
    Display and VPots are used for editing the parameters of the selected element

Function Buttons:
    Function buttons 1-14 selects tool on current toolpage
    Function button 15 decrements toolpage
    Function button 16 increments toolpage

Automation and other functions
    Not available at this moment   

Transport section:
    Rewind, Fastforward, Stop, Play and Record are linked with the transport control of the 
    editor application.
    Wheel moves locator, or controls Scrubspeed when Scrub is activated.
    Cursor keys scroll arrangment, or changes zoom factor when Zoom is activated.
    Frame Forward and Backward moves locator to next or previous frame, or next or previous
    second when used with shift button.
    PI and PO buttons change corresponding flags in editor, but sets left and right locator
    of editor to current position when used with shift button.
    Home and end buttons moves current locator to begin or end of the arrangement, or moves
    the current locator to the left or right locator when used with shift button.


JL-Cooper CS-10/2 interface
___________________________

Faders:
    The eight faders of the CS-10/2 are linked with the mixer Output elements faders at the 
    bottom of the mixer columns. The corresponding fader in the Editor mixer window is shown
    in red if the position of the CS-10/2 fader does not match with the current mixer fader. 
    The CS-10/2 display shows which column on the mixer is connected with the first physical fader. 
    Use the bank switch buttons F1/F2 to select	other columns on the mixer.

Fader Buttons:
	The function of these buttons depends on the selected mode.

Fader Buttons Mode Selection:
    The mode selection happens with the button located below the 4 leds (SOLO, MUTE, LOC, SEL).
    There are currently 6 Fader button modes: 

    SOLO: (SOLO led active)	
      Fader button controls solo button on Output element of coresponding mixer column.
    INPUT MUTE: (SOLO+MUTE led active)
      Fader button controls mute button on Input element of coresponding mixer column.
    OUTPUT MUTE: (MUTE led active)
      Fader button controls mute button on Output element of coresponding mixer column.
    GOTO MARKER: (LOC led active)
      Fader button moves the current locator to the selected marker position.
      (If SHIFT button is also pressed, markers 9-16 are selected, otherwise markers 1-8)
    DROP MARKER: (LOC+SEL led active)
      Fader button moves the selected marker to the current locator position.
      (If SHIFT button is also pressed, markers 9-16 are selected, otherwise markers 1-8)
    ARM TRACK: (SEL led active)
      Fader button controls first Track element track arming button of coresponding mixer column.

Rotary controls:
    The six rotary controls of the CS-10/2 are linked with the mixer Output elements pan controls at the
    bottom of the mixer columns. The corresponding pan potmeter in the Editor mixer window is shown 
    in red if the position of the CS-10/2 potmeter does not match with the current mixer pan control. 
    The CS-10/2 display shows which column on the mixer is connected with the first physical potmeter. 
    Use the bank switch buttons F1/F2 to select	other columns on the mixer.

Bank Switches F1/F2: 
    These switches control the mixer column number offset in relation to the CS-10/2 first fader, 
    first fader button and first rotary knob. By default the first fader/fader button/rotary knob 
    controls the corresponding functions of mixer column 1.
    Press F2 to increment the mixer column number offset by 4.
    Press F1 to decrement the mixer column number offset by 4.

Tool Page Selection F3:
    This button controls the selection of the tool page.
    Press F3 to select the next tool page.
    Press SHIFT + F3 to select the previous tool page.

Wheel Mode F4: 
    The wheel function has 2 modes:

    LOCATE: (right led above wheel active)
      In this mode, the wheel moves the current locator position without any audio being played.

    SCRUB: (left led above wheel active)
      In this mode, the wheel moves the current locator position while audio is being played.
      The 'move' sensitivity is affected by the arrangement horizontal zoom factor.

Tool Selections F5-F9:
    The first 5 tools from each tool page can be selected for the left mouse button by pressing the 
    F5-F9 buttons. Press SHIFT + F5-F9 to select the next 5 tools on each tool page.  

Transport buttons:
    They work the same way as the transport buttons on the Editor. 
    Press SHIFT + REW/FF to move the current locator to the beginning/end of the  arrangement.

Left/Right locators:
    The two buttons at the lower left and right of the wheel are assigned to the left and right 
    locators. Pressing these buttons will drop the left or right locator on the current locator. 
    Press SHIFT with these buttons to move the current locator to the left or right locator.	

Zoom and scrolling:
    The buttons are used for vertical and horizontal zooming of the arrange window.
    Press SHIFT with these buttons for vertical and horizontal scrolling of the arrange window.


Penny + Giles DC16
__________________

Faders:
    Fader controls volume fader or panning of the output element of the selected column. 
    The top line in the display shows which column on the mixer is connected with the first fader 
    on the console. Use the bank swith buttons to select other columns on the mixer and the 
    Volume/Pan button to select the fader mode.

Fader buttons:
    The function of these buttons depends on the selected mixer mode and locator mode. 
    In mixer mode the bottons can control the solo, mute in, mute out and the track insert of the 
    mixer. In locator mode the buttons can be used to set the first 16 markers or the position 
    the current locator on one of the first 16 markers.

Fader button mode:
    The eight buttons at the left top of the console select the function of the 16 fader buttons:

	Button 1:	Reserved
	Button 2:	Reserved
	Button 3:	Reserved
	Button 4:	Locator Mode
	  Pressing a fader button moves the current locator to the selected marker.
	  Pressing SHIFT with a fader button drops the selected marker on the current locator position.
	Button 5:	Input Mute
	  Fader buttons are linked with the mute button of the input element. 
	Button 6:	Track
	  Fader buttons are linked with the first track insert.
	Button 7:	Output Solo
	  Fader buttons are linked with the solo button of the output element.
	Button 8:	Output Mute
	  Fader buttons are linked with the mute button of the output element.

Control buttons:
    The buttons at the right of the console control various settings and modes:

	Button 1:	Bank Left
	  Move the faders 8 positions to the left.
	Button 2:	Bank Right
	  Move the faders 8 positions to the right.
	Button 3:	Volume/Pan 
	  Selects the mode of the faders on the console. 
          Led will be on when faders are linked with the panning of the output element.

	Button 4:	SHIFT button

	Button 5:	Zoom Horizontal Out/Scroll Left.
	Button 6:	Zoom Horizontal In/Scroll Right.
	Button 7:	Zoom Vertical In/Scroll Down.
	Button 8:	Zoom Vertical Out/Scroll Up.
	  These buttons control the zoom factor of the arrange window, or with pressing 
          the SHIFT button scroll the arrangement window.

	Button 9:	Punch In.
	Button 10:	Punch Out.
	Button 11:	Loop.

	Button 12:	Reserved
	Button 13:	Reserved
	Button 14: 	Reserved
	Button 15:	Reserved
	Button 16:	Scrub.
		This button put the recorder into scrub mode when the wheel is used.

Transport Buttons
    They work the same way as the transport buttons on the Editor. 
    Press SHIFT and REW/FF to Move the current locator to the beginning/end of the arrangement.

Left/Right Locator Buttons
    These buttons control the left and right locator.
	
	Button 1:	Goto Left Locator.
	Button 2:	Drop Left Locator.
	Button 3:	Drop Right Locator.
	Button 4:	Goto Right Locator.

Wheel:
    In normal operation, movements of the wheel will modify the current locator position. 
    When the scrub mode is selected, movements of the wheel will scrub the current locator.


Penny + Giles MM16
__________________

Faders:
    Fader controls volume fader or panning of the output element of the selected column. 
    The top line in the display shows which column on the mixer is connected with the first fader
    on the console. Use the bank swith buttons to select other columns on the mixer and the 
    Fader Mode button to select the fader mode.

Fader buttons:
    The function of these buttons depends on the selected mode.  The buttons can control 
    input mute, output mute, output solo and track insert of the mixer,
    and can be used to drop markers or to position the current locator on a marker.

Fader Mode (UTIL)
    This button selects the mode of the faders.  By default the faders are linked with 
    the volume control of the output element. With this button the faders can be linked 
    with the pan control of the output element.

Button Mode (EDIT)
    This button is used to select between different modes for the fader buttons.
    The bottom line in the display will show the selected mode.

    OUTPUT MUTE:  Fader buttons are linked with the mute button of the output element.
    OUTPUT SOLO:  Fader buttons are linked with the solo button of the output element.
    INPUT MUTE:   Fader buttons are linked with the mute button of the input element.
    TRACK:	  Fader buttons are linked with the first track insert of the column.
    DROP LOCATOR: Fader buttons drop a marker (1-16, 17-32 when SHIFT is pressed) on 
		  the current locator position.
    GOTO LOCATOR: Fader buttons move the current locator to the selected marker 
                  (1-16, 17-32 when SHIFT is pressed).

Left/Right Locators (SNAP/TEMPO)
    These two buttons are assigned to the left and right locators. Pressing these buttons 
    will drop left or right locator on the position of the current locator. 
    Press SHIFT + F8 to move the current locator to the left or right locator.
    The locator can be dropped while playing an	arrangement.

Shift (STORE)
    SHIFT button is always used in combination with other buttons.

Bank Switch (SEND)
    With this button you can link the faders and buttons with ones other than the first 
    16 mixer columns (ie. the next bank is selected). Each time the button is pressed the 
    offset of the columns will increment by 8. The display will show the number of the mixer 
    column that is linked with the first fader and button.
    Press SHIFT + SEND to decrement the offset by 8.

Scrubbing (HOLD)
    Use this button to select the scrub mode when the wheel is used. 
    The led in the button will be on when scrub mode is selected.

Tool Selection (F1-F7)
    The first 7 tools from each tool page can be selected for the left mouse button by pressing 
    the F1-F7 buttons. Press SHIFT + F1-F7 to select the next 7 tools on each page.
    Use the Tool Page Selection button to switch between different tool pages.

Tool Page Selection (F8)
    Pressing this button selects the next tool page.
    Press SHIFT + F8 to select the previous tool page.

Transport buttons:
    They work the same way as the transport buttons on the Editor. 
    Press SHIFT and REW/FF to Move the current locator to the beginning/end of the arrangement.


Wheel:
    In normal operation, movements of the wheel will modify the current locator	position 
    (right led above the will will be on). When the scrub mode is selected, movements of the 
    wheel will scrub the current locator (left led above the wheel will be on).

Zoom and scrolling (Arrow buttons):
    The buttons are used for vertical and horizontal zooming of the arrange window.
    Press SHIFT and these buttons to scroll the arrange window up and down or left and right.


CM-Automation Motor Mix
_______________________

Faders, solo, mute:
   They are linked with the volumne, mute and solo control on the mixer output element.

Record:
    These buttons are currently only linked with the track insert of the selected mixer column.  

Knobs:
    The function of the knob and the button below is defined by the selected mode with the 4 little 
    buttons at the right on the console.

	Button 1, Green LED:  Knob is linked with panning of output element.
                              Button is linked with the mute on the input element.
	Button 1, Yellow LED: Knob is linked with the vertical panning of the output element if available.
                              Button is linked with the mute button on the input element.
	Button 2, Green LED:  Knob is linked with the volume control on the first send element in the mixer column. 
                              Button is linked with the mute button on the fist send.
	Button 2, Yellow LED: Knob is linked with the pan control on the first send element in the mixer column. 
                              Button is linked with the mute button on the fist send.
	Button 3 and 4:	      Same function as button 2 but linked with the 2nd and 3rd send in the mixer column.
		
Left/Right:
   Depending upon the selection of Bank and Group, these button will select the next or previous 
   8 or 4 mixer columns.

Function Buttons:
    The function buttons at the left and right of the faders are parly defined:

	Play:		    Puts recorder into play mode.	
	Stop:		    Stops the recorder.
	Rewind:		    Puts recorder into rewind mode.
	Fast Forward:	    Puts recorder into fast forward mode.
	
Select Buttons:
    The function of the buttons on top of the console depend upon the selected mode, 
    which can be chosen by pressing SHIFT and one of the function buttons.
	
	Transport:
		Rew: 	Puts recorder into rewind mode.
		FF:	Puts recorder into fast forward mode.
		Stop:	Stops the recorder.
		Play:	Puts recorder into play mode.
		Rec:	Puts recorder into record mode.
		Pin: 	Controls punch in flag.
		Pout:	Controls punch out flag.
		Loop:	Controls loop flag.

	Locate:
		DrLl:	Drop left locator on current locator position.
		DrRl:	Drop right locator on current locator position.
		GtLl:	Move current locator to left locator.
		GtRl:	Move current locator to right locator.
		GtAs:	Move current locator to start of arrangement.
		GtAe:	Move current locator to end of arrangement.

	Zoom/Scroll (monitor):
		ZHIn:	Zoom arrangement window horizontal in.
		ZHOut:	Zoom arrangement window horizontal out.
		ZVIn:	Zoom arrangement window vertical in.
		ZVOut:	Zoom arrangement window vertical out.
		ScLe:	Scroll arrangement left.
		ScRi:	Scroll arrangement right.
		ScUp:	Scroll arrangement up.
		ScDo:	Scroll arrangement down.


JL-Cooper MCS-3000 / MCS-3800 interface and MCS Accessories (not MCS-3400)
__________________________________________________________________________

Faders, Mute, Solo
    The faders and buttons are linked with the volume, mute and solo control of the output 
    elements of the mixer columns.

Aux
    The function of this button is defined with the function buttons.
	F1 (Input Mute): The buttons are linked with the input mute control on the input element.
	F2 (Track Arm):	 The buttons are linked with the arming control	of the track insert.

Select:
    This button selects the column which is linked with the effect control.

Effect Control:
    The 8 buttons above the display selects which effect has to be controlled on the selected 
    column. The selected effect will be shown on the display.

	Page 1:	  Panning on output element. Both X and Y pan can be controlled.
	Page 2-4: Controls one of the first 3 sends of the column.
		  Press SHIFT + 2-4 to select Sends 4, 5 & 6. 

	Page 5-8: Controls one of the first 4 effects elements of the column. 
		  Press SHIFT + 5-8 to select effects elements 5 to 8.
	
	Knob 1-4: Used to control the selected parameters.  
	Knob 5:	  Use this knob to select the parameters to control.  
                  The names of parameters are shown on the bottom line of the display.

	Use Assign button to switch between parameter name or value display.

M-buttons:
	M1:	Controls punch in flag.
	M2:	Controls punch out flag.
	M3:	Controls loop flag.
	M4:	Places current locator on left marker.
		With SHIFT pressed places the left marked on the current locator.
	M5:	Places current locator on right marker.
		With SHIFT pressed places the right marker on the current locator.

W-buttons:
	These buttons are used to scrub with a constant speed, or with SHIFT pressed
	to move the current locator with a constant speed.
	W1-W3: Reverse.
	W5-w7: Forward.
	W8: Stops the scrub or move.

Wheel:
	The inner wheel is by default used to move the current locator.
	With function button F7, this default can be changed to scrub locator.
	The outer wheel is always used to scrub the locator.

Zoom and scrolling (Arrow buttons):
	The buttons are used for vertical and horizontal zooming of the arrange window.
	Pressing SHIFT and these buttons will scroll the arrange window up and down or
	left and right.

Bank:
	Use these buttons to select other banks for the faders and fader buttons.
	Bank 1:	Select column 1-8.	
	Bank 2: Select column 9-16.	
	Bank 3: Select column 17-24.	
	Bank 4: Select column 25-32.

	Note: Number of columns moved depends upon the number of expander units in the system.

Transport buttons:
    They work the same way as the transport buttons on the Editor. 
    Press SHIFT and REW/FF to Move the current locator to the beginning/end of the arrangement.

Keypad:
    The keypad can in combination with the stop and play button of the transport be used 
    to control current locator, the markers and general arming and disarming of the track inserts.
    They operate in the same way as the PC keyboard (number keypad) for the Editor.

	Mode locate   = Ins (to insert markers).
	Set locate    = Set current locator value.
	Last          = * (for arming).
	Clear Cancel  = / (for disarming).
	Enter         = Enter (to move markers).
	+/-           = - (for specifying a range).

Optional MCS-3000X Fader Expanders
__________________________________

    Up to 7 additional fader expander units can be connected to the MCS-3800 console and are 
    supported by the Console Manager.  
    Always add additional expander units on the left hand side of the main unit and use the 
    settings below to create a valid setup.

	+----+----+-...-+----+--------------+
	| 7  | 6  |     | 1  | MCS-3800     |
	+----+----+-...-+----+--------------+

	Dipswitch settings of expander units:
		Exp.   #4   #3   #2   #1
		1      OFF  OFF  OFF  OFF
		2      OFF  OFF  OFF  ON
		3      OFF  OFF  ON   OFF
		4      OFF  OFF  ON   ON
		5      OFF  ON   OFF  OFF
		6      OFF  ON   OFF  ON
		7      OFF  ON   ON   OFF

Optional MCS-Bridge units
_________________________

    Up to 8 bridges can be connected to the MCS-3800 console and are supported by the Console Manager.  
    Joystick on bridge is used for 2D panning on output element.
    The two knobs on each channel of the bridge can be used to control panning of output element
    or panning/volume control of the send elements. 
    Press knob and turn to select the parameter to control.
    Display on the bridge will show the currently selected parameters.
    Use settings below to create a valid setup:

	+----+----+-...-+----+----+
	| B7 | B6 |     | B1 | B0 |
	+----+----+-...-+----+----+---------+
	| E7 | E6 |     | E1 | MCS-3800     |
	+----+----+-...-+----+--------------+

	Dipswitch settings of expander units:
		Bridge #4   #3   #2   #1
		0      OFF  ON   ON   ON	
		1      OFF  OFF  OFF  OFF
		2      OFF  OFF  OFF  ON
		3      OFF  OFF  ON   OFF
		4      OFF  OFF  ON   ON
		5      OFF  ON   OFF  OFF
		6      OFF  ON   OFF  ON
		7      OFF  ON   ON   OFF

Optional MCS-PANNER or MCS-ORBITER (motorised) Surround Panners
_______________________________________________________________

    Currently one surround panner is supported. The panner will always be connected with the panning 
    control of the mixer output element.
    Use the buttons S1-8 to select the mixer column. 
    The column selection is independent of the bank selection of the main unit.

	DIP-switch settings:
		Switch 1, 2 and 4 = OFF, switch 3 = ON


Mackie HUI Interface
____________________

Fader columns:
    Fader controls volume fader of the output element of the selected column.
    The display shows the column name if defined, or the column number if not.
    Mute button controls the mute of the output element of the selected column.
    Solo button controls the solo of the output element of the selected column.
    Auto button is currently not used (reserved for later use).
    Insert button selects the column for effect control (see Effect control).
    Rec/Rdy button controls the arming of the track insert in the column.
    Only one track insert per column can be controlled.
    Use the Rec/Rdy All button to arm or disarm all available tracks.
    The V-pot controls the panning of the output element or the panning or volume of the send elements. 
    Which one is under control is defined by the buttons at the left side of the V-pots.
    Pan controls the X-panning of the output element.
    Send A - Send E controls the volume of the first five sends.
    When SHIFT is on, the panning of the sends is controlled or Pan-Y of the output element is controlled.
    By default, the V-sel buttons controls the mute button of the sends, or the mute of the input element. 
    When the Mute button is on, the V-Sel button is always linked with the mute of the input element.
    Use the bank and channel buttons to control other columns of the mixer.

Effect Control:
    Use the Insert button to select the column and the function buttons for selection of the 
    effect of the selected column.
    The scroll knob shifts the parameters across the screen.
    The Bypass button is always linked with the bypass button of the insert.
    Assign button is used to switch between parameter name or value display.

Keypad:
    The keypad can in combination with the stop and play button of the transport be used to control 
    current locator, the markers and general arming and disarming of the track inserts. 
    They operate in the same way as the pc keyboard keypad for the Editor.
	=	  Set current play locator.
	/ 	  Track disarming.
	* 	  Track arming.
	- 	  Specifies a range.
	Clr	  Cancels previously entered numbers.
	Enter     Move markers.
	+	  Insert markers.

Transport buttons:
    They work the same way as the transport buttons on the Editor. 
    Press SHIFT and REW/FF to Move the current locator to the beginning/end of the arrangement.


Wheel:
    Function of the wheel is defined by the Scrub or Shuttle button on the right side of the wheel.


Using TASCAM TM-D4000 with Console Manager
__________________________________________

    The TM-D4000 interface uses the CS-10 emulator mode for communication between mixer/recorder and
    the console.  Add the CS10 Emulator device to the Machine Control List (MIDI & MC SETUP display).
    Enable TRA, REC and select SRC of this device.  
    Tape transport and numerical buttons are always available.  Faders and buttons (CUT) are only 
    available when external control on console is selected on CS-10 emulator.  Reference manual of
    TM-D4000 for more detailed desciption of usage.

Transport buttons:
    They work the same way as the transport buttons on the Editor. 
    Press SHIFT + REW/FF to move the current locator to the beginning/end of the  arrangement.

Faders:
    Fader controls volume fader or panning of the output element of the selected column. 
    Use the bank swith buttons to select other columns on the mixer and the Fader Mode buttons 
    to select the fader mode.

Fader Buttons:
    The function of these buttons depends on the selected mode.  They can be used to control solo,
    input mute and output mute of the selected column.  Use the bank swith buttons to select other 
    columns on the mixer and the Button Mode buttons.

Left and Right arrow:
    Used to select banks or to change horizontal zoom settings.
    Use Arrow Mode buttons to change the arrow mode.

Wheel:
    Movements of the wheel will modify the current locator position (select Jog/Shuttle button).
    Scrub mode is not implemented.
    
Button Mode Buttons:
    Shift + Button 7: Solo mode
    Shift + Button 8: Output mute mode
    Shift + Button 9: Input mute mode

Fader Mode Buttons:
    Shift + Button 4: Output volume mode
    Shift + Button 5: Output pan mode

Arrow Mode Buttons:
    Shift + Button 1: Bank selections
    Shift + Button 2: Horizontal zoom

Note:
    The numerical buttons are only available when shift is pressed.  
    Other interfaces can also be used to control mixer/recorder functionality as there are:
        - RS-422 interface (8mm DTRS device)
        - Midi Mixer Map interface (MIDI FADERS)

Known issues:
    There's no feedback of tape transport.
    Feedback of button leds is not working.
    Console Manager can't control the faders in the CS-10 emulator mode.

An alternative for the CS-10 emulation mode is the usage of MMC-interface for transport
control and MIDI Mixer Map interface for volume and panning control.  Advantage of these
modes is the feedback of faders and transport status.


Spirit Digital 328 (Open loop)
______________________________

    Interface for Spirit Digital 328 V1.6.
    In the Midi Fader Bank mode the 16 faders and 16 knobs can be programmed to 
    control volume and pan of the first 16 columns of a mixer.  
    The MIDI controllers need to be programmed as described in the table below:

        Fader 1  = Controller No 1:  Chan 1   Id 7 (0x07)
        Fader 2  = Controller No 2:  Chan 2   Id 7 (0x07)
        ....
        Fader 16 = Controller No 16: Chan 16  Id 7 (0x07)
	Knob 1   = Controller No 17: Chan 1   Id 10 (0x0A)
	Knob 2   = Controller No 18: Chan 2   Id 10 (0x0A)
        ....
	Knob 16  = Controller No 32: Chan 16  Id 10 (0x0A)


Spirit Digital 328 V2 (closed loop)
___________________________________

    Interface for Spirit Digital 328 V2.
    This firmware version has capabilities to update the faders and controls on the console
    when changes are made in SSHDR1/REd/Mixtreme mixer caused by user interacetion or 
    automation.  Additionally, it makes it possible to use mute and solo buttons of the 
    console.
    The MIDI controllers need to be programmed as described in the table below:

        Fader 1  = Controller No 1:  Chan 1   Id 7 (0x07)
        Fader 2  = Controller No 2:  Chan 2   Id 7 (0x07)
        ....
        Fader 16 = Controller No 16: Chan 16  Id 7 (0x07)
	Knob 1   = Controller No 17: Chan 1   Id 10 (0x0A)
	Knob 2   = Controller No 18: Chan 2   Id 10 (0x0A)
        ....
	Knob 16  = Controller No 32: Chan 16  Id 10 (0x0A)
	Solo 1   = Controller No 33: Chan 1   Id 16 
	Solo 2   = Controller No 34: Chan 2   Id 16 
	....
	Solo 16  = Controller No 48: Chan 16  Id 16 
	Mute 1   = Controller No 49: Chan 1   Id 17
	Mute 2   = Controller No 50: Chan 2   Id 17 
	....
	Mute 16  = Controller No 64: Chan 16  Id 17

    To enable closed loop operation, the Digital 328 must be put into the correct
    automation mode.  Press <Menu> and scroll up or down until Automation Setup is
    highlighted.  Press <Enter> and with the PARAM encoded set MIDI dynauto to ON,
    press the down cursor keey and set the automation mode to 'CONTROLLER'.  
    


Sony 9-pin Slave
________________

    Basic functionality is provided for transport control, locating and track arming using the Sony P2 protocol.

    In general, installing an RS422 card is the reliable method for connecting to a controller.
    Contact Soundscape Digital Technology or your distributor to purchase a recommended RS422 card.


Sony 9-Pin Master
_________________

    Basic funtionality is provided for transport control, locating and track arming (through dialog).


MMC Slave Interface
___________________

    Basic functionality is provided for Transport control, locating and track arming using 
    MMC protocol.  Detection of device id is done automatically when first command from 
    controller is received.  
    Sometimes it is necessary to reset or restart the controller after Console Manager is running
    and the MMC Slave interface is enabled, in order to start working correctly.


Midi System Real Time Interface
_______________________________

    Interface which translates sytem real time messages START (0xFA), CONTINUE (0xFB) 
    and STOP (0xFC) to Soundscape Editor Commands.


MIDI Mixer Map Interface
________________________

    Programmable interface which is able to map all available MIDI controller messages to all
    available parameters of the mixer.  Configurations can be saved and restored for later use.


General Advanced MIDI Interface
_______________________________

    General advanced MIDI interface gives the ability to control every parameter of the
    128 mixer columns. The MIDI messages are sent and received in the NRPN format. 
    Up to 16384 parameters are defined, so there are 128 controller parameters available per mixer column


Pinguin PDAE Interface
______________________

    This is a beta version.
    Interface for Pinguin PDAE software (16-bit).
    Requires an additional tool from Pinguin in order to use it.
    Contact Pinguin for more information.





IF YOU ENCOUNTER ANY BUGS, PLEASE CONTACT:

via email: bugreport@soundscape-digital.com

FOR TECHNICAL SUPPORT, PLEASE CONTACT:

Soundscape Digital Technology Ltd
Unit A1, Caxton Place, Pentwyn
CARDIFF
UK
Tel: +44 1222 540 333
Fax: +44 1222 540 332

Or you can reach us on our web site: http://www.soundscape-digital.com
Or by email: support@soundscape-digital.com




